| |
|
-
MPG+
Series: TC - PAM version
-
SHDSL-Digital Pair Gain System
Exartech MPG+, an SHDSL (Symmetric single pair
High bit rate DSL) Digital Pair Gain System, conveys
uncompressed PCM Voice channels in it. This system
provides
4/8/12 voice channels over a single twisted pair
subscriber line. MPG+E provide an SHDSL (G.SHDSL)
interface by using existed twisted pair between RT
and LU. It can support POTS (Voice) and Ethernet
interface (e.g. Internet
access) as your wish. With Exartech Scarab-E
(Ethernet modem), MPG+E can extend
Ethernet transmission distance to 2~5 Km by SHDSL.
MPG+ series are mainly used to meet the
demand of subscribers (or potential subscribers) at
those areas, where the number of subscriber lines
cannot be expanded in proportion to the increase of
subscribers. Without digging ground or placing
cable, it immediately solves subscriber line
shortage problem.
-
-
Key Features:
-
Ø
Optional 4, 8,12 clear 64Kbps channels over one single copper
pair
-
Ø
High speed in transmission when Modem (Internet) or FAX
connected
-
Ø 12Khz, 16Khz Metering (Reverse Polarity) function for
payphone
-
Ø
Remote power feeding for Remote Unit
-
Ø
RT box is designed to be weather protected, water resistance,
anti-bug, rust, fire…
-
Ø
On board power supply decreases the harm of power failure
-
Ø
4/8/12 channels and broadband units could be installed
in the universal 19” shelf
-
Ø
Powerful NMS to monitor system status
-
Ø
Short, surge, and lightning protections comply to ITU K-20,
and K-21
-
Ø
Enable direct connectivity towards data/IP network (Option)
-
Ø
Enable delivery services from POTS to XDSL, Ethernet…
-
Ø
Convent TDM networks and combine IP network
-
Ø
Support CLIP (Caller ID)
-
Ø
Support Bypass function
-
Ø
Support Concentration (Option)
-
Ø
Support repeaters to extend transmission distance (Option)
-
-
Specification:
-
DSL Line Transmission
Characteristics
-
Ø
Line Code Format : TC PAM
-
Ø
COT/RT DSL Impedance: 135 Ohms
-
Ø
Bit Error
Rate :
<10-7
-
Ø
Range: up to 5.4 km at 0.4mm copper wire(depend
on rate)
-
Ø
Connector: Wire wrap pins (rear access)
-
Transmission Characteristics of VF of LU & RT
-
Ø
Return Loss: ERL >15 dB (600~3.4 KHz) / SRL >12 dB
(300~600 Hz)
-
Ø
Insertion Loss: 4.0 dB ± 0.5dB
-
Ø
Channel Cross Talk: <-65 dBm0
-
Ø
Idle Channel Noise: <25 dBrnc
-
Ø
Frequency Response 300~3000 Hz: -0.6~+3
dB
-
LU Side:
-
Ø Ringing
detection: 16 ~ 60 Hz, > 45 Vrms
-
Ø Metering Detection Frequency: 16 KHz / 12 KHz ± 500 Hz, >-10 dBm
-
Ø Input
impedance: 600 ohm or 900 ohm (for customer requirement)
-
Ø Off-Hook
DC Resistance: <400 ohms
-
Ø Operating
Loop current: <100 mA
-
Ø Encoding:
A law (meet ITU-T G.711 requirements)
-
Ø VF
parameter: meet ITU-T G.712 requirements
-
Ø On
hook data transmission delay: < 50mS
-
Ø Connector:
Wire wrap pins (rear access)
-
RT Side:
-
Ø
Ringing generation:
>45 Vrms, 25 ± 1Hz (20 ± 1Hz)
-
Ø
Transmission range: <800 ohms (including telephone)
-
Ø
Metering signal Generation: 12 K/16 KHz ± 1%, >-2.5 dBm
-
Ø
On-Hook
Loop Voltage: >45 VDC
-
Ø
Loop Current:
>20 mA
-
Ø
On-Hook
Detection: >1500 ohms
-
Ø
Off-Hook
Detection: <800 ohms
-
Ø
Connector:
Terminal Block (Pluggable Rising Clamp Type)
-
Power:
-
Ø
LU
Operating Voltage: -36~-72 VDC
-
Ø
Power Supply Unit: On-board Power Module
-
Ø
RT Power Source: Remote Feeding / or Local power
-
Ø
Feeding
current: < 60mA
-
Ø
RT Power Source: 200V(MPG+4)/
250V(MPG+8)/
300V(MPG+12)
-
Ø
Power Consumption:
-
|
|
MPG+
4 |
MPG+
8 |
MPG+
12 |
|
Full Load 16 |
496.0 W |
346.0 W |
440.0 W |
|
For a DSL (LU+RT+DSL) |
31.0 W |
21.6 W |
27.5 W |
|
For each DSL Line |
3.2 W |
4.1 W |
3.6 W |
|
For each LU |
11.8 W |
8.7 W |
10.7 W |
|
For each RT |
6.4 W |
8.8 W |
13.2 W |
-
Operation Environmental Conditions: (indoor version,
LU):
-
Ø
Temperature:
-10~+60
°C
-
Ø
Humidity:
up to 100% (Non-condensing)
-
Transportation:
-
Ø Temperature: -20 ~
70 C
-
Ø Humidity:
up to 100% Condensing
|

MPG+
Larger View

LU cards Larger
View

RT Box Larger View

Repeater Larger View |